IR Plus

IR M1

The IR Plus features a distributed infrared emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.

The rack mounted or remotely located IR M1 Control Center comes standard with support for up to four IR emitters. Each emitter runs back to the modulator via a CAT5e cable, providing the audio and power needed to support the remote emitter. Each emitter has a coverage area of 18,000 sq. ft.

The IR Plus Control Center can also provide audio over Wi-Fi. Connect the IR M1 to a Wi-Fi multicast router or in-house network you can stream audio over Wi-Fi to the Williams AV WaveCAST app (available in the iOS app store or Google Play store).

Description

The IR Plus features a distributed infrared emitter array architecture allowing up to four emitters either stacked together for large room arrays or distributed throughout the room to accommodate wings in room design, balconies or other obscured venue locations.

The rack mounted or remotely located IR M1 Control Center comes standard with support for up to four IR emitters. Each emitter runs back to the modulator via a CAT5e cable, providing the audio and power needed to support the remote emitter. Each emitter has a coverage area of 18,000 sq. ft.

The IR Plus Control Center can also provide audio over Wi-Fi. Connect the IR M1 to a Wi-Fi multicast router or in-house network you can stream audio over Wi-Fi to the Williams AV WaveCAST app (available in the iOS app store or Google Play store).

IR M1

Dimensions: 19” (W) x 1.75” (H) x 8.2” (D)
(48.3 cm x 4.5 cm x 20.8 cm)
Weight: 5.2lb. (2.4 kg)
Color: Black
Rack Mount: Single Rack Unit
Power Supply: International Desktop Supply
Input: 36 W, 110-240 VAC 50-60 Hz
Output: +48VDC, 0.75A center-positive
Power Switch: Rocker switch with LED
Signal to Noise Ratio: 67 dB (typical)
Modulation: FM Wideband, +50kHz deviation, 50uS pre-emphasis
Carrier Frequency: Selectable, 2.3/2.8 or 3.3/3.8MHz
Frequency Response: 40 to 16,000Hz, +1 dB, -3dB, electrical response
Total Harmonic Distortion: Less than 2%, electrical response
Audio Processor Functions: DSP based; Compression 1:1, 1.5:1, or 2:1; High-pass and low-pass filter frequency control
Auto Carrier Shut-Off: Adjustable timer shuts off carrier when no audio is present. Adjustable through webpage.
Infrared Test LED: Dual IR LED for receiver testing, monitoring, and audio signal testing.
Audio Input: (2x) Combination 3-pin XLR, 1/4” (TRS) jack for balanced or unbalanced line level, or balanced or unbalanced microphone with selectable phantom power
Dante: Optional
Internal Test Tone: 400 Hz internal test tone selectable as audio input source for setup and diagnostics
Remote Configuration: Available through embedded website
Headphone Output: (2) 1/4″ headphone jacks on front panel for monitoring CH A and CH B audio inputs
Emitter Output Jack: Four RJ-45 ports for CAT5e cables; provides +48VDC Power, RS-485 communication, and Baseband signals for IR transmission.
Operating requirements: 0-50ºC ambient temperature, non-condensing, non-corrosive atmosphere
Approvals: CE, FCC, RoHS, RCM, WEEE, CB Scheme, ISED, VCCI
Warranty: 2 years on Modulator, 90 days on accessories

Warranty

2 Years

No Videos Are Available

Request a Demo

  • This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.